Application	Suitable types	Reasons
Power supply smoothing	Aluminum electrolytic	High capacity, high ripple current
Audio frequency coupling	Aluminum electrolytic Tantalum Polyester / polycarbonate	High capacitance High capacitance, small size Cheap, but values not as high as electrolytic
RF coupling	Ceramic COG Ceramic X7R Polystyrene	Small, cheap, low loss Small cheap, but higher loss than COG Very low loss, but larger than ceramic
RF decoupling	Ceramic COG   Ceramic X7R	Small, low loss. Values limited to around 1000 pF Small, low loss, higher values available than for COG types
Tuned circuits	Silver mica Ceramic COG	Close tolerance, low loss Close tolerance, low loss, although not as good as silver mica

• Sometimes, capacitors are used to store charge for high-speed use. That's what a flash does. Big lasers use this technique as well to get very bright, instantaneous flashes.
• Capacitors can also eliminate ripples. If a line carrying DC voltage has ripples or spikes in it, a big capacitor can even out the voltage by absorbing the peaks and filling in the valleys.
• A capacitor can block DC voltage. If you hook a small capacitor to a battery, then no current will flow between the poles of the battery once the capacitor charges. However, any alternating current (AC) signal flows through a capacitor unimpeded. That's because the capacitor will charge and discharge as the alternating current fluctuates, making it appear that the alternating current is flowing.

Capacitor type	Dielectric used	Features/applications	Disadvantages
Paper Capacitors	Paper or oil-impregnated paper	Impregnated paper was extensively used for older capacitors, using wax, oil, or epoxy as an impregnate. Oil-Kraft paper capacitors are still used in certain high voltage applications. Has mostly been replaced by plastic film capacitors.	Large size. Also, paper is highly hygroscopic, absorbing moisture from the atmosphere despite plastic enclosures and impregnates. Absorbed moisture degrades performance by increasing dielectric losses (power factor) and decreasing insulation resistance.
Metalized Paper Capacitors	Paper	Comparatively smaller in size than paper-foil capacitors	Suitable only for lower current applications. Has been largely superseded by metalized film capacitors
PET film Capacitor	Polyester film	Smaller in size when compared to paper or polypropylene capacitors of comparable specifications. May use plates of foil, metalized film, or a combination. PET film capacitors have almost completely replaced paper capacitors for most DC electronic applications. Operating voltages up to 60,000 V DC and operating temperatures up to 125 °C. Low moisture absorption.	Temperature stability is poorer than paper capacitors. Usable at low (AC power) frequencies, but inappropriate for RF applications due to excessive dielectric heating.
Kapton Capacitor	Kapton polyimide film	Similar to PET film, but significantly higher operating temperature (up to 250 °C).	Higher cost than PET. Temperature stability is poorer than paper capacitors. Usable at low (AC power) frequencies, but inappropriate for RF applications due to excessive dielectric heating.
Polystyrene Capacitor	Polystyrene	Excellent general purpose plastic film capacitor. Excellent stability, low moisture pick-up and a slightly negative temperature coefficient that can be used to match the positive temperature co-efficient of other components. Ideal for low power RF and precision analog applications	Maximum operating temperature is limited to about +85 °C. Comparatively bigger in size.
Polycarbonate Plastic Film Capacitor	Polycarbonate	Superior insulation resistance, dissipation factor, and dielectric absorption versus polystyrene capacitors. Moisture pick-up is less, with about ±80 ppm temperature coefficient. Can use full operating voltage across entire temperature range (−55 °C to 125 °C)	Maximum operating temperature limited to about 125 °C.
Polypropylene Plastic Film Capacitors	Polypropylene	Has become the most popular capacitor dielectric [citation needed]. Extremely low dissipation factor, higher dielectric strength than polycarbonate and polyester films, low moisture absorption, and high insulation resistance. May use plates of foil, metalized film, or a combination. Film is compatible with self-healing technology to improve reliability. Usable in high frequency applications due to very low dielectric losses. Larger value and higher voltage types from 1 to 100 μF at up to 440 V AC are used as run capacitors in some types of single phase electric motors.	More susceptible to damage from transient over-voltages or voltage reversals than oil-impregnated Kraft paper for pulsed power energy discharge applications.
Polysulphone Plastic Film Capacitors	Polysulfone	Similar to polycarbonate. Can withstand full voltage at comparatively higher temperatures. Moisture pick-up is typically 0.2%, limiting its stability.	Very limited availability and higher cost
PTFE Fluorocarbon (TEFLON) Film Capacitors	Polytetra- fluoroethylene	Lowest loss solid dielectric. Operating temperatures up to 250 °C, extremely high insulation resistance, and good stability. Used in stringent, mission-critical applications	Large size (due to low dielectric constant), and higher cost than other film capacitors.
Polyamide Plastic Film Capacitors	Polyamide	Operating temperatures of up to 200 °C. High insulation resistance, good stability and low dissipation factor.	Large size and high cost.
Metalized Plastic Film Capacitors	Polyester or Polycarbonate	Reliable and significantly smaller in size. Thin metallization can be used to advantage by making capacitors "self healing".	Thin plates limit maximum current carrying capability.
Stacked Plate Mica Capacitors	Mica	Advantages of mica capacitors arise from the fact that the dielectric material (mica) is inert. It does not change physically or chemically with age and it has good temperature stability. Very resistant to corona damage	Unless properly sealed, susceptible to moisture pick-up which will increase the power factor and decrease insulation resistance. Higher cost due to scarcity of high grade dielectric material and manually-intensive assembly.
Metalized Mica or Silver Mica Capacitors	Mica	Silver mica capacitors have the above mentioned advantages. In addition, they have much reduced moisture infiltration.	Higher cost
Glass Capacitors	Glass	Similar to Mica Capacitors. Stability and frequency characteristics are better than silver mica capacitors. Ultra-reliable, ultra-stable, and resistant to nuclear radiation.	High cost.
Class-I Temperature Compensating Type Ceramic Capacitors	Mixture of complex Titanate compounds	Low cost and small size, excellent high frequency characteristics and good reliability. Predictable linear capacitance change with operating temperature. Available in voltages up to 15,000 volts	Capacitance changes with change in applied voltage, with frequency and with aging effects.
Class-II High dielectric strength Type Ceramic Capacitors	Barium titanate based dielectrics	Smaller than Class-I type due to higher dielectric strength of ceramics used. Available in voltages up to 50,000 volts.	Not as stable as Class-I type with respect to temperature, and capacitance changes significantly with applied voltage.
Aluminum Electrolytic Capacitors	Aluminum oxide	Very large capacitance to volume ratio, inexpensive, polarized. Primary applications are as smoothing and reservoir capacitors in power supplies.	Dielectric leakage is high, large internal resistance and inductance limits high frequency performance, poor low temperature stability and loose tolerances. May vent or burst open when overloaded and/or overheated. Limited to about 500 volts.
Lithium Ion Capacitors	Lithium ion	The lithium ion capacitors have a higher power density as compared to batteries and LIC’s are safer in use than LIB’s in which thermal runaway reactions may occur. Compared to electric double layer capacitor (EDLC), the LIC has a higher output voltage. They both have similar power densities, but energy density of an LIC is much higher.	New technology.
Tantalum Electrolytic Capacitors	Tantalum oxide	Large capacitance to volume ratio, smaller size, good stability, wide operating temperature range, long reliable operating life. Extensively used in miniaturized equipment and computers. Available in both polarized and unpolarized varieties. Solid tantalum capacitors have much better characteristics than their wet counterparts.	Higher cost than aluminum electrolytic capacitors. Voltage limited to about 50 volts. Explodes quite violently when voltage rating, current rating, or slew rates are exceeded, or when a polarized version is subjected to reverse voltage.
Electrolytic double-layer capacitors (EDLC) Supercapacitors	Thin Electrolyte layer and Activated Carbon	Extremely large capacitance to volume ratio, small size, low ESR. Available in hundreds, or thousands, of farads. A relatively new capacitor technology. Often used to temporarily provide power to equipment during battery replacement. Can rapidly absorb and deliver larger currents than batteries during charging and discharging, making them valuable for hybrid vehicles. Polarized, low operating voltage (volts per capacitor cell). Groups of cells are stacked to provide higher overall operating voltage.	Relatively high cost.
Alternating current oil-filled Capacitors	Oil-impregnated paper	Usually PET or polypropylene film dielectric. Primarily designed to provide very large capacitance for industrial AC applications to withstand large currents and high peak voltages at power line frequencies. The applications include AC motor starting and running, phase splitting, power factor correction, voltage regulation, control equipment, etc..	Limited to low frequency applications due to high dielectric losses at higher frequencies.
Direct current oil-filled capacitors	Paper or Paper-polyester film combination	Primarily designed for DC applications such as filtering, bypassing, coupling, arc suppression, voltage doubling, etc...	Operating voltage rating must be derated as per the curve supplied by the manufacturer if the DC contains ripple. Physically larger than polymer dielectric counterparts.
Energy Storage Capacitors	Kraft capacitor paper impregnated with electrical grade castor oil or similar high dielectric constant fluid, with extended foil plates	Designed specifically for intermittent duty, high current discharge applications. More tolerant of voltage reversal than many polymer dielectrics. Typical applications include pulsed power, electromagnetic forming, pulsed lasers, Marx generators, and pulsed welders.	Physically large and heavy. Significantly lower energy density than polymer dielectric systems. Not self-healing. Device may fail catastrophically due to high stored energy.
Vacuum Capacitors	Vacuum capacitors use highly evacuated glass or ceramic chamber with concentric cylindrical electrodes.	Extremely low loss. Used for high voltage high power RF applications, such as transmitters and induction heating where even a small amount of dielectric loss would cause excessive heating. Can be self-healing if arc-over current is limited.	Very high cost, fragile, physically large, and relatively low capacitance.